To open an iPhone 5 back cover, the first step is to remove the metal plate covering the phone. The metal plate is held in place by four screws. Before removing the cover, make sure that you are reinstalling the screws in the same places. Next, unscrew two screws that secure the EMI shield on the bottom right side of the battery. The battery cable is attached to the logic board via the flex cable. Disconnect the battery cable from the logic board with a spudger. Once the EMI shield is removed, remove the battery cable from the logic board.
How Do You Take The Back Cover Off An iPhone 5?
How to open the back cover of an iPhone is a relatively simple procedure, but it can be tricky to do correctly. You need to be patient and carefully lift the back cover off the phone. To do this, the back cover slides up a few millimeters, then lift it off with your fingers. Be careful not to damage the screws holding the back assembly in place, so make sure you use a #000 screwdriver.
Once you have removed the back cover, place your tweezers between the front and the back assembly. Place them by the speaker/mic holes, near the metal frame. The screws should be popped out easily. If you have a Phillips head screwdriver, you can remove them. Depending on the location of the screws, you may need a flathead screwdriver. Once you have removed the screws, you can now remove the back cover.
How Do I Open My iPhone 5 Without Suction Cup?
To open the iPhone 5 back cover without using a suction cup, you need to first unplug the phone. The front panel is attached to the phone by ribbon cables and locks. You can use a plastic opening tool to pull apart the front panel from the phone’s housing. With one hand, press the power button and pull the plastic tool to separate the housing and the metal plate holding the home button.
To remove the glass from the iPhone 5, first use a security screwdriver to unscrew the two screws that secure the display to the phone’s back cover. Then, take a tweezers and use them to pry out the three screws that hold the shield. Then, remove the screw and the protective case. Once the protective case has been removed, you can replace the glass on the iPhone.
To remove the screen, heat the back case using a hair dryer or a heatgun. Next, use a spudger to gently scrape out the edge of the screen. The screen is sealed with dual-sided adhesive strips. Lift the display by a few centimeters and carefully peel it off. Ensure that the wires haven’t come loose. If you cannot remove the display cover, try to disassemble the remaining parts of the iPhone.
How Do You Open The Back Of An iPhone?
First, you will need to remove the front assembly by sliding it towards the back of the phone. While holding the front assembly in this position, use the plastic tool or your finger to connect the connector on the top of the home button. It can be tricky to connect the connector, so be careful. When the phone boots, the home button should work. Now, slide the metal covers back in place. Now, you can replace the screen.
After that, you can start prying and levering the back of the iPhone 5 to remove the battery. Be sure to keep the volume buttons in one hand when prying and levering. Heat is not a good idea because the adhesive might tear. Moreover, the process of opening the back of the iPhone 5 can cause damage to your hands if you do not use the right tools. In such a case, you can sell your broken phone.
How Do I Open My iPhone Without A Screwdriver?
To open the iPhone 5 back cover without a screwdrived, you must first turn off the device. Next, use a screwdriver to remove the two screws at the base of the lightning port. Once the screws are removed, you can now lift the screen up. You can use the suction cup to lift the display to a 90-degree angle. Next, find the L-shaped connector bracket at the lower-right side of the assembly. This bracket will have four tri-point screws. You must remove them so you can reach the battery connector and the screen connector. Both are attached to ribbons.
First, you must make sure that you use a Pentalobe screwdriver. You can use a small one like the TS1 screwdriver, which fits the tiny screws on the iPhone. If you cannot find one, you can purchase a new one or use a screwdriver. If you can’t find one, you can also use a tupperware container. This will save you a lot of time.
How Do I Take The Back Off My Phone?
The battery on your iPhone 5S/5C can be removed in three different ways. To take off the battery, the simplest way is to pull the back assembly outwards, towards the charging port. To make it easier, heat up the back assembly lightly using a hair dryer. Next, peel off the two adhesive strips that attach the battery to the metal frame. You should now be able to remove the entire back assembly.
To remove the display, slide the screen down half an inch. The screen will release from the casing. Be careful not to scratch the connector cables that are attached to the display. After you have detached the display, pull the release tab and then remove the battery. Depending on how glued the battery is, you may need a pry tool to remove it. Be careful not to damage the battery connector by using a screwdriver or pry bar.
How Do You Open An iPhone 5S Screen?
There are two basic steps to open an iPhone 5S screen. First, remove the screws holding the security cover in place. A Torx screwdriver is required for this. Second, separate the two sides of the metal housing from the plastic bezel. Then, pry the two sides of the screen apart. Once you have separated them, the two pieces of metal will separate. You can now insert the new screen into the housing.
To begin, start by removing the two screws on the bottom of the display assembly. They are the same size as the screws on the bottom of the phone. Next, unscrew the four screws holding the shield that covers the display cable connector. You should now be able to pull the display assembly from the body of the phone. Ensure that you don’t scratch the metal back assembly. Once the metal shield is removed, you should use the plastic spudger tool to remove the ribbon cables.
Next, remove the top glass and bottom LCD. This assembly will allow you to access the screen. Now, you should be able to remove the bottom LCD from the device. If the LCD has become black, you should replace it. This is also the best way to repair a cracked screen. It may take a bit of patience, but you will be happy you did it yourself. It’s also a great way to keep your iPhone 5S in pristine condition.
How Can I Open My iPhone Without Special Tools?
If you don’t have any special tools to open iPhone 5, don’t worry, there’s no need to break your device. Simply follow these steps. Using a small suction cup, pry up the screen. Then, unscrew the two pentalobe screws that secure the front assembly to the logic board. Make sure that you don’t pull the screen too far or you may damage the connector cables.
Depending on the model, you may need a different method to open the back cover of the iPhone 5. The iPhone 5S doesn’t have a pull tab mechanism, so you must carefully pry it out with a thin tool. Be very careful not to puncture the cell as you pull out the battery. Once you have separated the back cover from the back of the phone, you should place the battery and antenna back into it.
You can also use a suction cup to lift the display of your iPhone. A ring-type suction cup is ideal, but you can also use a vacuum suction cup. Alternatively, you can use a guitar pick. If you don’t have one of these tools, you can also use a heat source, such as a gel or sand-filled bag. The heat will loosen the adhesive that secures the display to the phone. You’ll also need a suction cup to remove the screen, which should be relatively easy. Then, you can place all of your parts back in a plastic bag to prevent dust from accumulating.
Learn More Here:
1.) Apple Website
3.) iPhone models
4.) iPhone wiki
